Take the 2-minute tour ×
Gardening & Landscaping Stack Exchange is a question and answer site for gardeners and landscapers. It's 100% free, no registration required.

A little over a year ago, after complaining about the amount of cord I had to use with our electric leaf blower I was gifted an inexpensive gas blower. A Ryobi 150 mph 400 CFM Gas Blower Vac from home depot to be precise. It probably wouldn't have been the one I would've chose, but hey. Complaining about gifts is never a good idea.

I mixed up some gas for the two stroke engine, but admittedly I did eyeball it. It started right up, and worked great. I used it for the next 30 minutes or so until it ran out of gas. At this point I needed to buy some new gas. I mixed up this next batch very carefully, and about two weeks later I went to use it again. It would not start, didn't start. Its a year later and If I was going to return it I should've done it months ago.

I'd like to get it started, but have little experience with trouble shooting small engines. I am a computer programmer, not a lawn care specialist. But, I'd love to learn. And I do have an internet connection. I am a bit stumped. Where should I begin. What could be wrong?

note: looking at the reviews online this 'not starting' or tough to start seems to be a common problem.

share|improve this question

migrated from diy.stackexchange.com Sep 17 '12 at 19:14

This question came from our site for contractors and serious DIYers.

    
Did you follow the starting procedure to the letter? –  The Evil Greebo Sep 17 '12 at 19:01
    
@The Evil Greebo Yep, sure did. –  matchew Sep 17 '12 at 19:11
1  
Could be neighbors put sugar in your gas. (I have no love for leaf blowers) –  DA. Sep 17 '12 at 22:27
    
I don't have any experience of leaf blowers and chainsaws, but our lawnmower would need priming every time I used it. If your leaf blower is cheap, perhaps it doesn't have a priming pump, and you're expected to fill it every time you use it? If it works and then doesn't a few weeks later as a rule, it does seem fuel or lubricant (eg. poor seals resulting in wet spark plugs?) is the problem. –  winwaed Sep 18 '12 at 13:07
    
FWIW, I see that this engine does have a primer pump. –  bstpierre Sep 18 '12 at 16:39

1 Answer 1

up vote 3 down vote accepted

Here's what I've done on my two-stroke chainsaw when it has refused to start:

  • Remove and replace spark plug; check the gap.
  • Remove and clean [with an air compressor] or replace air filter. (I just blow it out, I haven't yet replaced the filter.)
  • If you see gunk when you're removing these parts, clean it up. (Because of all of the sawdust and bar oil, the chainsaw accumulates a lot of gunk. I don't know how dirty your leaf blower will get.)

These are very easy steps -- I'm usually a complete failure at engine/machine repair and even I can do these without ending up with a pile of parts that I have to bring my friendly local mechanic for reassembly. For tools, you'll need a spark plug (deep) socket, an air compressor with a blower fitting, and maybe a screwdriver to open the engine case.

I've also seen replacing the fuel filter as a suggestion, but haven't needed to do this yet. The steps above always get it restarted.

share|improve this answer
    
I am going to mark this as the answer, but it did not solve my problem. I really think the piece of equipment is just cheap junk. Thanks for the help. –  matchew Oct 10 '12 at 18:20

Your Answer

 
discard

By posting your answer, you agree to the privacy policy and terms of service.

Not the answer you're looking for? Browse other questions tagged or ask your own question.